He-VA TIP Roller

Category:

Description

Introduction

More than just rolls!

HE-VA have one of the largest Rolls ranges on the market and the 3-Section Tip Roller makes up approximately 75% of all HE-VA rolls sold in the UK.

A unique combination of design features and heavy duty construction ensures true contour following and even weight distribution for level seedbeds, moisture retention, uniform germination, better yields and reduced risk of stone damage.

All rolls have the powerful built-in SAT (Special Active Transfer) system to spread the frame weight evenly across the machine width.

Sizes range from 4.5m to 10.2m, each size comes in 3 different variations, all fitted with NG rings, HD – 8 spoke 510mm (20″), HD Plus – 9 spoke 560mm (22″) and XHD – 10 spoke  620mm (24″). New Generation rings (NG) come standard with a 5-year warranty.

A full range of Shattaboards, Slicerboards, Straw Tines and Top Cutter are available to fit all Tip Rollers, turning each set of rolls into a cost effective cultivator.

From shed to field the driver doesn’t need to leave the tractor cab as the rolls can be put to work in seconds simply and safely straight from the tractor seat. Just pull into the field, unfold using the tractor hydraulics and you are ready to go.

Folding is just as simple, each 3-Section machine folds up to 2.5m (2.7m for 9.5 and 10.2m machines) Each wing section locks into a transport cradle once in the fully folded position increasing road transport safety and giving peace of mind that they stay where they should at all times.

Features

Weight Transfer System

Unique SAT System – Special Active Transfer

All rolls have the powerful built-in SAT system to spread the frame weight evenly across the machine width.

Cambridge Rolls without HE-VA automatic weight balancing tend to exert the highest ground pressure on the centre roller section. This roller section carries the weight of the drawbar, wheel frame and hydraulics as well as its own weight, far more than the two wing sections.

With a basic roller set up there is no weight transfer and the uneven weight distribution is great as can be seen above.

Even with a basic sprung weight transfer system the hinges at either end of the centre section prevent weight being spread evenly.

The HE-VA SAT system is spring loaded and as the outside roll sections are attached with centre pivot hinges, weight transferred evenly across the full width of the Cambridge Rolls.

Contour Following

The key to any set of Rolls successfully improving soil consolidation is weight, and getting the weight on to the soil. The Tip-Roller achieves this by featuring five Pivot Points, three centre pivots plus two more where the wings are joined to the main frame. Giving independent floatation on each section; this allows the roller to follow the contours in the most undulating of ground conditions and ensures constant ring to soil contact. 

Heavy Duty Design

The Tip Rollers folding mechanism has a deep wing link pivot with Teflon coated steel bushing top and bottom to provide strength for cultivation as well as rolling.

The rings are mounted on 60mm axles for strength and longevity. These axles run on 4 bolt bearings protected inside u-profile steel.

The Cambridge Rolls axle on the wing sections of the 8.2, 9.5 and 10.2m have a centre bearing as an additional support.

Fold in Seconds

Simple, safe folding – what else do you expect from a HE-VA

Folding Sequence 3 Section Tip Roller

Transport position HE-VA Rolls   

Cambridge Rolls in transport position.

Lift wings off cradles HE-VA Rolls   

Swinging the side section into working position.

Swing side sections working HE-VA Rolls   

Side section in working position.

 Tip side sections of HE-VA Rolls  

Tip the rolls forward until the
cylinder bottoms.

 Tip rolls forward until cylinder bottoms  

Tip the rolls forward until the cylinder bottoms.

 HE-VA rolls ready to work The HE-VA rolls are ready to work.

 

Transport & Storage

HE-VA’s 3 section Cambridge Rolls design supports the side section horizontally in a positive locking cradle reducing noise when travelling.

In the completely folded position the weight of the wings is carried between the tractor and transport wheels improving stability.

  

Ring Profile

HE-VA rolls are available with a choice of ring types. All carefully designed to cope with today’s higher machine weights but retain the time-proven qualities of traditional ring engineering, the range includes new multi-spoke developments created to meet customer demand and changing farming methods.

New generation rings come standard with a 5-year warranty.

 

510mm 21" HE-VA Rings 9 Spoke HE-VA Rings 10 spoke HE-VA Rings
8 spoke Cambridge and Breaker
510mm / 20″
9 spoke Cambridge and Breaker
560mm / 22″
10 spoke Cambridge and Breaker
620mm / 24″
 
8 spoke HE-VA Rings 9 spoke HE-VA Rings 10 spoke HE-VA Rings
8 spoke Cambridge only
500mm / 20″
9 spoke Cambridge only
550mm / 22″
10 spoke Cambridge only
600mm / 24″

 

        

Models

Cambridge Rolls 4.5m – 10.2m
RING TYPE                             Cambridge Only (Standard)   Cambridge & Breaker (Standard)
WIDTH   Ring Size 500mm 8 Spoke 550mm 9 Spoke 600mm 10 Spoke 510mm 8 Spoke 560mm 9 Spoke 620mm 10 Spoke
WORKING
4.5m
TRANSPORT
2.46m
WEIGHT KG
RINGS
AXLE (mm )
1990
57
60
2230
57
60
2542
57
60
2260
87
60
2540
87
60
2990
87
60
WORKING
5.4m
TRANSPORT
2.46m
WEIGHT KG
RINGS
AXLE (mm)
2430
69
60
2730
69
60
3164
69
60
2690
105
60
3100
105
60
3456
105
60
WORKING
6.3m
TRANSPORT
2.46m
WEIGHT KG
RINGS
AXLE (mm)
2840
78
60
3250
78
60
3617
78
60
3140
123
60
3710
123
60
4442
123
60
WHEELS: 10.0 / 75 X 15.3 – 10 PLY      *WHEELS: 11.5 / 80 x 15.3 – 10 PLY
WORKING
7.3m
TRANSPORT
2.46m
WEIGHT KG
RINGS
AXLE (mm
3520
90
60
3860
90
60
4273
90
60
3840
143
60
4430
143
60
4872
143
60
WORKING
8.2m
TRANSPORT
2.46m
WEIGHT KG
RINGS
AXLE (mm)
3840
102
60
4100
102
60
4645
102
60
4190
157
60
4700
157
60
5528
157
60
WHEELS: 11.5 / 80 X 15.3 – 10 PLY
WORKING
9.5m
TRANSPORT
2.46m
WEIGHT KG
RINGS
AXLE (mm)
4740
118
60
5030
118
60
5662
118
60
5180
180
60
5770
180
60
6730
180
60
WORKING
10.2m
TRANSPORT
2.46m
WEIGHT KG
RINGS
AXLE (mm)
5020
126
60
5310
126
60
5650
126
60
5690
196
60
6220
196
60
6850
196
60
WHEELS: 400 / 60 X 15.3 – 14 PLY

Technical Information

Cambridge Rolls 4.5m – 10.2m
HE-VA HD 3 section Cambridge Rolls – 500mm Roller Rings
Model Roller Size Working Width -m Working Width -ft Transport Width -m Weight kg
1063053-50 500mm 4.5m 15′ 2.20m 1990
1063054-50 500mm 5.4m 17’8″ 2.20m 2430
1063055-50 500mm 6.3m 20’6″ 2.46m 2840
1063058-50 500mm 7.3m 24′ 2.46m 3520
1063056-50 500mm 8.2m 27′ 2.46m 3840
1063059-50 500mm 9.5m 30’10” 2.5m 4740
1063051-50 500mm 10.2m 33’4″ 2.5m 5020
HE-VA HD 3 section Cambridge & Breaker Rolls – 510mm Roller Rings
Model Roller Size Working Width -m Working Width -ft Transport Width -m Weight kg
1063053-46 510mm 4.5m 15′ 2.20m 2260
1063054-46 510mm 5.4m 17’8″ 2.20m 2690
1063055-46 510mm 6.3m 20’6″ 2.46m 3140
1063058-46 510mm 7.3m 24′ 2.46m 3840
1063056-46 510mm 8.2m 27′ 2.46m 4190
1063059-46 510mm 9.5m 30’10” 2.5m 5180
1063051-46 510mm 10.2m 33’4″ 2.5m 5690
HE-VA XHD 3 section Cambridge Rolls – 600mm Roller Rings
Model Roller Size Working Width -m Working Width -ft Transport Width -m Weight kg
1063053-60 600mm 4.5m 14’8″ 2.46m 2542
1063054-60 600mm 5.4m 17’7″ 2.46m 3164
1063055-60 600mm 6.3m 20’7″ 2.46m 3617
1063058-60 600mm 7.3m 24′ 2.46m 4273
1063056-60 600mm 8.2m 27′ 2.46m 4645
1063059-60 600mm 9.5m 31’2″ 2.5m 5662
1063051-60 600mm 10.2m 33’5″ 2.5m 6017
HE-VA XHD 3 section Cambridge & Breaker Rolls – 620mm Roller Rings
Model Roller Size Working Width -m Working Width -ft Transport Width -m Weight kg
1063053-62 620mm 4.5m 14’8″ 2.46 2990
1063054-62 620mm 5.4m 17’7″ 2.46m 3456
1063080-62 620mm 6.3m 20’6″ 2.46m 4442
1063082-62 620mm 7.3m 24′ 2.46m 4872
1063081-62 620mm 8.2m 27′ 2.46m 5528
1063083-62 620mm 9.5m 30’10’ 2.5m 6730
1063084-62 620mm 10.2m 33’4″ 2.5m 7258
NOTE: The 8.2, 9.2 and 9.5 metre wide Cambridge Rolls have a 50mm gap for the support bearing hangers in both wing sections
4.5m – 8.2m Machines fitted with pivoting towing eye Ø50mm – 66630757028
9.5m – 10.2m Machines fitted with pivoting towing eye Ø50mm – 66630757017
Included: Road Lights as Standard
HDplus Cambridge Ring Rolls – 550mm Diameter
Model No. Roller size Working width Transport width Weight kgs
1063053-59 550mm 4.5m 2.2m 2230
1063054-59 550mm 5.4m 2.2m 2730
1063055-59 550mm 6.3m 2.46m 3250
1063058-59 550mm 7.3m 2.46m 3860
1063056-59 550mm 8.2m 2.46m 4100
1063059-59 550mm 9.5m 2.5m 5030
1063051-59 550mm 10.2m 2.5m 5310
4.5m – 8.2m Machines fitted with pivoting towing eye Ø50mm – 66630757028
9.5m – 10.2m Machines fitted with pivoting towing eye Ø50mm – 66630757017 (drawbar details at rear of booklet).
HDplus Cambridge & Breaker Ring Rolls – 560mm Diameter
Model No. Roller size Working width Transport width Weight kgs
1063053-54 560mm 4.5m 2.2m 2540
1063054-54 560mm 5.4m 2.2m 3100
1063055-54 560mm 6.3m 2.46m 3710
1063058-54 560mm 7.3m 2.46m 4430
1063056-54 560mm 8.2m 2.46m 4700
1063059-54 560mm 9.5m 2.5m 5770
1063051-54 560mm 10.2m 2.5m 6220
4.5m – 8.2m Machines fitted with pivoting towing eye Ø50mm – 66630757028
9.5m – 10.2m Machines fitted with pivoting towing eye Ø50mm – 66630757017 (drawbar details at rear of booklet).

Options & Accessories

Shattaboards & Slicerboards

Shattaboards

Slicerboards

Shattaboards & Slicerboards cultivate, level and consolidate in front of the roller, transforming the rolls into an all round cultivation tool.

Hydraulic operation enables the levelling board to be retracted when necessary and controls the working angle. The locking device links the springboards together harnessing their combined strength to improve levelling.

The Slicerboard knife edges slice into clods on heavy ground enhancing the tilth created by the board.

• Close coupled – strength and reliability
• Height and angle adjustment
• Adjustable wearing paddles – extend life
• Locking device – enhances leveling ability

 

Shattaboards & Slicerboards – including locks
Model No. Type Working Width   To fit Weight kgs
1063303-00LD     Shattaboards     4.5m All rings   475
1063304-00LD Shattaboards 5.4m All rings 549
1063305-00LD Shattaboards 6.3m HD 624
1063505-00LD Shattaboards 6.3m HDplus/XHD     624
1063507-00LD Shattaboards 7.3m All rings 716
1063506-00LD Shattaboards 8.2m All rings 792
1063509-00LD Shattaboards 9.5m All rings 957
1063510-00LD Shattaboards 10.2m All rings 1000
1063603-00LD Slicerboards 4.5m All rings 475
1063604-00LD Slicerboards 5.4m All rings 549
1063605-00LD Slicerboards 6.3m HD 624
1063805-00LD Slicerboards 6.3m HDplus/XHD 624
1063807-00LD Slicerboards 7.3m All rings 716
1063806-00LD Slicerboards 8.2m All rings 792
1063809-00LD Slicerboards 9.5m All rings 957
1063810-00LD Slicerboards 10.2m All rings 1000

 

Deduct Price for Locking Device
Model No. To fit working width     Weight kgs
1063403-00     4.5m 55
1063404-00 5.4m 64
1063405-00 6.3m 74
1063407-00 7.3m 86
1063406-00 8.2m 97
1063409-00 9.5m 112
1063410-00 10.2m 120
1063301-00 Edge plate for Shattaboard, pair
Straw Tines

Straw Tines on Tip RollersTwo rows of sprung finger tines that can turn a set of HE-VA Tip rolls into a true multi-purpose machine, capable of helping growers reduce their reliance on chemicals in combating pest and weed problems.

Following initial cultivation passes, the heavy-duty Tip Rollers fitted with Straw Tines can be put to work pre-drilling with the tines providing shallow soil movement to generate a surface tilth.

Rows of breaker rings provide a firming action and a corrugated, weather-proof finish ready for the drill. The aggressive stirring action of the tines disturbs and disrupts slug activity, destroying clutches of eggs before they hatch.

Tip Rollers equipped with Straw Tines can also be used following the combine to evenly spread and break up crop residues, prompting more rapid breakdown.

Straw Tines Technical Information
Model Description
1063905-02 2 rows 16mm Straw Tines for 6.3m HD plus & XHD Tip Rolls
1063907-02 2 rows 16mm Straw Tines for all 7.3m Tip Rolls
1063906-02 2 rows 16mm Straw Tines for all 8.2m Tip Rolls
1063909-02 2 rows 16mm Straw Tines for all 9.5m Tip Rolls
Top-Cutter

photo showing SlicerboardsDesigned to assist in cover crop destruction, the Top-Cutter can be fitted as an option to HE-VA Tip Rollers

Mounted ahead of the main cultivation elements on the chosen machine, the roller is equipped with six blades which span its full working width. With downforce generated by the Tip Roller, the blades provide a transverse chopping action.

• V-Profile rings on the host machine work at 90 degrees to the knife roller ensuring crop residues are comprehensively dealt with

• Blades are arranged in a chevron pattern to evenly load the roller and avoid vibrations being generated when the machine is running at speed

 

Top-Cutter Technical Information
Model Description
1067410-23 Top cutter for 6.3m HD Tip rolls
1067410-25 Top cutter for 6.3m HD plus and XHD Tip rolls
1067410-27 Top cutter for all 7.3m Tip rolls
1067410-29 Top cutter for all 8.2m Tip rolls
1067410-31 Top cutter for all 9.5m Tip rolls
Multi-Seeder Fitting Kit

photo showing Multi seeder fitting kitWith a Multi-Seeder mounted on your Tip Roller it becomes an oilseed rape and/or cover crop drill making it even more useful on the farm.

  • Individual metering roller for each outlet giving higher accuracy.
  • RDS Control box
  • In cab variable rate control
  • Simple calibration and rate setting
Other Optional Extras
Model Description
1063080-11 10.0/75 x 15.3 – 14 ply tyre in lieu for 4.5 – 6.3m HD
1063080-10 11.5/80 x 15.3 – 14 ply tyre in lieu for 6.3m HD
1063080-09 400/60 x 15.5 – 14 ply tyre in lieu for 7.3m + 8.2m**
1063098-08 Hydraulic brakes
1063098-07 Air Brakes
1060801003 Drawbar extension (500mm) 9.5m – 10.2m
1060801001 Drawbar extension (500mm) 4.5m – 8.2m
*NB Maximum carrying capacity including seeder = 200kg
Note: The 8.2, 9.5 and 10.2 metre wide 3-section rolls have a 50mm gap for the support bearing hangers on all three sections.
**Transport width increases to 2.56m
NB: Seeder/applicator fitting kit available on request

Draw Bar Options

Pivoting Towing Eye – Standard
  Weight (KG) Description Pivoting towing eye - standard
66630757028 13 Pivoting towing eye “Standard” Ø50mm mounted with M16 bolts
Pivoting Towing Eye – Strong
  Weight (KG) Description
66630757017 20 Pivoting towing eye “Strong” Ø50mm mounted with M20 bolts
Pivoting Towing Eye – High Quality
  Weight (KG) Description
66630757046 20 Pivoting towing eye “High Quality” Ø50mm mounted with M20 bolts
Pivoting Towing Eye – Strong 85°
  Weight (KG) Description
66630757041 20 Pivoting towing eye “Strong 85°” Ø50mm mounted with M20 bolts
Ball Hitch
  Weight (KG) Description
66630757023 26 Ball hitch f/Ø80mm ball mounted with M20 bolts
Pivoting Crossbar Cat III
  Weight (KG) Description
66630757034 81 Lower link mounted pivoting crossbar Cat III Ø36.5mm pins mounted with M20 bolts
Pivoting Crossbar Cat IV
  Weight (KG) Description
66630757045 88 Lower link mounted pivoting crossbar Cat IV Ø50mm pins mounted with M20 bolts
Towing Eye Bush
  Weight (KG) Description  
660438132 0.3 Bush for towing eye Ø50mm / Ø33.5mm reduces from Ø50mm to Ø33.5mm
NOTE: To upgrade the drawbar on your trailed HE-VA machine, please ensure the change is clearly marked on your order.